Acoustics & Music Theory
why it sounds like that
Concept

Instrument design — where it appears

The choices a maker has, as against the consequences those choices force. The recurring finding is that the choices are far fewer than they look: a flare, a strike point or a hole position usually has one narrow range that works and a great deal of space that does not.

Named by 7 essays across 3 fields — each of them below, with the objects they name alongside it.

Re-gauging at a fixed tension: how close sheep gut comes to breaking. Holding the tension at 700 newtons and re-gauging every string to suit the standard, the diameter each note needs goes as one over its frequency — so the stress goes as the frequency squared, and the margin against breaking falls the same way. At A = 392 the worst note has 1.79 times the stress sheep gut will take; at A = 466 it has 1.27. The margin reaches one at A = 525 hertz, which is far above anything the four hundred years of climb reached.

It was never the strings that stopped the climb

Every figure so far holds the instrument still and moves the standard. History did the opposite — instruments were rebuilt to suit the pitch, string by string. Hold the tension instead and each string's gauge is forced: the diameter goes as one over the frequency and the stress as its square. Gut breaks at A = 525 hertz and steel at 604, and the climb stopped at 466. The ceiling was somewhere else entirely.

tuning · Pitch standard A family resemblance, in the heights rather than in the frequencies. The peak heights of trumpet, F horn, tenor trombone, plotted against peak number rather than against frequency. The three differ in length by a factor of 2.4 and their frequency series cannot be made to overlap; their heights agree to 3.2 decibels on average and their Qs to a factor of 1.30. The agreement improves up the series — 6.9 decibels at the first peak and 1.6 at the 8th — which is an earlier claim arriving as a measurement: a family has one voice because it has one filter, and the filter is visible in what the bore pushes back with and not in where its resonances are.

A family resemblance in the heights

Trumpet, horn and trombone differ in length by a factor of two and a half, so their frequency series cannot be laid over one another. Their impedance peaks agree to three decibels in height and to thirty per cent in Q, peak for peak, and the agreement improves with peak number. An earlier essay inferred that a family has one voice because it has one filter; the solver can now be asked directly.

instruments · Bore profile One vent on a cone, over the notes it has to serve. A cone's modes are a full harmonic series, so the mode a register vent has to keep is the octave rather than the twelfth, and its pressure node sits at half the sounding length measured from the virtual apex. The apex is a fixed point of the instrument and the bell end is not, so every fingering moves the ideal position and there is one hole. The upper line is how much the vent spoils the fundamental, which is what it is for; the lower is how much it damages the octave, which is the cost. Their ratio runs from 451.2 at F♯4 down to 1.9 at B♭3 — a factor of 235 across a single register. The vent is placed at 37 per cent of the longest sounding length, which is where the worst fingering is least badly served.

The vent a cone cannot place

A clarinet's register key has to spoil a fundamental and leave a twelfth. A saxophone's has to spoil a fundamental and leave an octave, whose pressure node sits at half the sounding length from the virtual apex — and the apex is a fixed point while the bell end is not. Over one register the ideal position moves by a factor of two, and one hole is right for one note.

instruments · Tone holes The flare that makes a series harmonic, and how narrow it is. Every combination of a flare exponent and a station at which the flare begins, shaded by how far the bore's resonance series is from a harmonic series over partials 2 to 8, in cents. The best is 4.6 cents at an exponent of 1.00 beginning 43 per cent of the way along, against 127 cents for a plain cylinder, 21 for a plain cone and 26 for a Bessel horn of the exponent used everywhere else. Only 2.1 per cent of the surface is within five cents of the minimum, so the shape is forced rather than chosen — which is what three centuries of empirical brass design were finding.

The flare that makes a series harmonic

Every figure until now treats a partial as n times a fundamental, and the whole of brass instrument design is the business of making that true. A plain cylinder is 127 cents from a harmonic series and a plain cone is 21; the best flare found by sweeping is 4.6, and only two per cent of the swept surface comes within five cents of it. The shape is forced rather than chosen.

timbre · Harmonic series A woodwind cannot be pulled to a new standard. Every earlier figure computes strings, because a string's tension and gauge give a closed-form scaling law. A wind instrument does not have one, and this is why. To move from 440 to 415 hertz the player pulls out 11.7 millimetres at the joint, which lengthens the sounding tube of every fingering by the same absolute amount — so the interval each note drops is a fixed length against a shrinking one, exactly the shape of an end correction. The tuning note lands where it should and nothing else does: D3 is 67 cents sharp of where it belongs and G5 is 75 flat, a spread of 142 cents across the compass. A rebuilt instrument has no such problem — scale every length by one ratio and every mode moves by the same interval, and the tone-hole lattice cutoff moves with it, from 1766 hertz to 1666, which is 101 cents and therefore the same instrument transposed. That is the difference between an afternoon and a year.

A woodwind cannot be pulled to a new standard

Every earlier essay computes strings, because a string has a closed-form scaling law. A wind instrument does not. Pulling out at the joint lengthens every fingering's sounding tube by the same number of millimetres, which is a fixed length against a shrinking one — so the tuning note lands and the compass spreads by 142 cents. The strings could be regauged in an afternoon; the winds had to be rebuilt.

tuning · Pitch standard Where one arch can put a bar's second and third partials. The plane of the second and third partials, with the path a single arch traces through it as it is cut deeper, for 4 arch lengths from 50 to 100 per cent of the bar. Every path starts at the plain bar's 2.756 and 5.404 and runs up and to the right. The xylophone's target of 3 and 6 lies on them: reach the second partial and the third is there. The marimba's target of 4 and 10 lies above every one of them — the best any of these arches manages while holding the second partial at 4 is 9.176, which is 149 cents short. A marimba's third partial is not something one cut can place, and that is a statement about the shape of the cut rather than about the maker.

One cut cannot place two partials

An arch cut into a bar's underside is one knob, and a maker aims it at two targets. Swept across every arch length, the path it traces through the plane of the second and third partials passes through the xylophone's 3 and 6 — dead through it, within a tenth of a cent at the natural arch length — and under the marimba's 4 and 10 by between 149 and 326 cents. Hitting one target means missing the other, and that is why a marimba bar's underside is not a simple arch.

instruments · Struck bar The bare bore does not care which valve is down. The distance in cents of partials 2 to 8 from the harmonic series that fits them best, at each valve combination of a B♭ trumpet, computed with the mouthpiece in place and again with the bore alone. The bare bore is flat — 0.78 cents from best to worst across the whole set — so the length changes nothing. With one cup serving all of them the same bore runs 19.53 to 24.83 cents, a spread of 5.30, because the cup's popping frequency stays at 642 hertz while the series underneath it drops.

One cup and seven lengths

A trumpet is seven tubes with one mouthpiece serving all of them, and the harmonicity of its resonance series is a different number in every position — 19.5 cents open, 24.8 with all three valves down. The bare bore is flat across the same seven lengths to within eight-tenths of a cent, so none of it is a length problem. It is the cup, standing still while the series walks past it, and pressing all three valves does to the series exactly what fitting a mouthpiece 56 per cent of the catalogue depth would do.

timbre · Harmonic series

Named alongside it

The objects these essays reach for when they reach for this one.

BoreIntonationBrassCutoffResonanceHarmonic seriesNodePartialPitch standardScalingTone holeBreaking stress

All concepts