Brass — where it appears
Named by 18 essays across 4 fields — each of them below, with the objects they name alongside it.
Only two shapes make a series
A tube's length sets where its modes are and its shape sets whether they are a series at all — and of every shape a maker could choose, exactly two give evenly spaced modes. Neither of them is the shape of a trumpet. Webster's equation says how far the others miss by, and the answer is a quarter of a semitone for the obvious ones and four cents for the family brass bells actually belong to.
What the mouthpiece is actually for
A cup and a throat look like a comfort fitting and are a component. Put a real one on the front of a real bore in the horn equation and the whole mode series slides sideways by about a seventh of its own spacing — which is exactly the distance between a series whose second resonance is 1.85 times the spacing and one whose second resonance is the second harmonic. The flare decides whether the modes are evenly spaced; the mouthpiece decides which harmonic each one is.
A horn has one length per partial
Every tube until now has had an acoustic length: its physical length plus a correction for the wave carrying on past the opening. A flaring bore does not have one. Its second mode behaves as though the tube were 164 centimetres long and its eighth as though it were 154, and the ten centimetres between them are the same physical fact — a fixed correction against a shrinking wavelength — arriving as a hundred cents.
The hand goes in, and the note jumps
A horn player's hand closes the bell and the pitch falls — 19 cents, then 55, then 132, then four hundred, accelerating the whole way. Then, in the last half per cent of closure, it stops falling and lands a semitone above where it started. An earlier essay guessed the mechanism was the boundary condition changing kind and the series going odd-only. It is not. The series never changes at all.
A resonance has a strength as well as a frequency
What eleven earlier essays drew is a row of frequencies, because the solver behind it has no losses and a lossless resonance has no width. Put the losses in and every one of them acquires a height and a Q — and the hand closing a horn's bell turns out to take away nine and a half per cent of the instrument's total support before giving all of it back, in a window a few per cent wide where the horn is genuinely hard to play.
The cutoff a maker can actually measure
A trumpet's bell cutoff computed from the geometry alone comes to 1,150 hertz against a published 1,500, and the calibration was the first thing that left owing. Measuring the model the way a maker measures the instrument — sweep a loudspeaker in, find where the impedance peaks stop — gives 1,593. The discrepancy was almost entirely in the formula, and on a bore whose flare is spread rather than concentrated the same formula is out by a factor of twenty-nine.
The higher note speaks sooner and takes longer
Up a brass instrument the settling time in milliseconds falls by a factor of seven and the settling time in periods rises by a factor of three. Both curves are read off the same impedance sweep, both are monotone over most of the compass, and they point in opposite directions — so the slowest note of the instrument depends entirely on which clock is used to time it.
A family resemblance in the heights
Trumpet, horn and trombone differ in length by a factor of two and a half, so their frequency series cannot be laid over one another. Their impedance peaks agree to three decibels in height and to thirty per cent in Q, peak for peak, and the agreement improves with peak number. An earlier essay inferred that a family has one voice because it has one filter; the solver can now be asked directly.
The flare that makes a series harmonic
Every figure until now treats a partial as n times a fundamental, and the whole of brass instrument design is the business of making that true. A plain cylinder is 127 cents from a harmonic series and a plain cone is 21; the best flare found by sweeping is 4.6, and only two per cent of the swept surface comes within five cents of it. The shape is forced rather than chosen.
What a cup does to the support
The mouthpiece's job was settled four essays ago and settled in cents: it decides which harmonic each mode is. Measured instead in the currency a player buys one in — how hard the note pushes back, and how narrowly it holds its pitch — the cup does something else entirely. It multiplies the support in the written register by about five, and it puts a ceiling on the instrument that the bell had not put there.
The bell is tuned for the cup
Sweeping a brass bell's two flare parameters found a shape that makes the resonance series harmonic to four and a half cents. Bolt the mouthpiece that instrument is actually played with onto it and the series is twenty-five cents out — worse than a plain cone. The flare and the cup are not two independent choices, and the best bell for a maker to build is one that is deliberately wrong.
The resonator at the far end
A cup at the throat owns the top of a brass instrument and puts a ceiling on it. A straight mute is a second closure at the other end of the same air column, and the prediction written down before it was computed was that it would push that ceiling further down. It does the opposite: the ceiling goes from C6 to E♭6, and it goes there by reviving exactly the resonances the cup had killed.
The mouth that decides nothing
Twelve figures across six earlier essays draw a trumpet with a 124-millimetre bell, and not one of them draws any other. Opened from 32 millimetres across to 280, the bell's own boundary moves by a factor of eighteen and almost nothing else moves at all: the instrument's registration, the sharpness of its notes in the written register, and where it runs out are all within a semitone of themselves. The reason is that the resonances are held by the walls, and a bell cannot reach them.
The partials the tube makes itself
Eleven earlier essays compute a passive linear resonator, and none of them ever says so. At a real fortissimo the air in a brass instrument is not linear: a compression outruns a rarefaction, the wave leans forward as it travels, and the fourth partial of a loud trumpet note is seventy decibels louder than a scaled-up quiet one — generated in the tube rather than at the lips. How much of it happens is an integral over the bore, and it is why a flugelhorn cannot be blown into being a trumpet.
What the tongue actually removes
The question this essay was written against asked for an impulse: a tongued attack, a martelé stroke and a struck key all deliver one before the steady drive begins. The arithmetic refuses the framing. A tongue release does carry energy at the note's own frequency, and it is worth 0.17 milliseconds on a trumpet against a settling time of 62 — capped at about 1.13 over the resonance's Q. What articulation is worth is the ramp it removes, and that is about half the ramp's own length: 44 milliseconds, and very nearly the same 44 on every wind instrument in the collection.
One cup and seven lengths
A trumpet is seven tubes with one mouthpiece serving all of them, and the harmonicity of its resonance series is a different number in every position — 19.5 cents open, 24.8 with all three valves down. The bare bore is flat across the same seven lengths to within eight-tenths of a cent, so none of it is a length problem. It is the cup, standing still while the series walks past it, and pressing all three valves does to the series exactly what fitting a mouthpiece 56 per cent of the catalogue depth would do.
Which notes go brassy first
Wave steepening manufactures partials at exact integer multiples of the note being played. A brass instrument's resonances are not at integer multiples of anything, and twelve earlier essays have measured how far off they are without ever putting the two on one axis. Put them there and a manufactured partial never lands on a peak — never once, at any note, by a miss that is the same number of hertz every time. So the alignment cannot be what decides which notes blare, and the thing that does turns out to be the bell.
The throat that decides both
Eight earlier essays draw a tube eleven millimetres across and none of them draws another. Opened from six millimetres to twenty-two, it does exactly what was predicted to the loss in the walls — and it moves the radiation loss three times further, in the opposite direction, and monotonically, which the bell does not. So the two ends of a brass instrument do not divide the two losses between them. One end owns one loss and both ends own the other.
Named alongside it
The objects these essays reach for when they reach for this one.
BoreResonanceImpedanceCutoffHorn equationQuality factorNormal modeDampingHarmonic seriesBoundary conditionHelmholtz resonanceMouthpiece