Acoustics & Music Theory
why it sounds like that
Concept

Normal mode — where it appears

One of the frequencies at which a bounded system will vibrate on its own, set by its geometry and its boundary conditions rather than by whatever excites it. A tube's modes are what a player selects between; a room's are why its bass is uneven.

Named by 8 essays across 3 fields — each of them below, with the objects they name alongside it.

What a chorus costs on one bridge. The sixty-decibel time of the longest-lived mode of two coupled strings at 262 hertz, against how far apart they are tuned. Below the bifurcation at 4.5 cents the pair splits its decays and one mode rings on; above it the pair splits its frequencies instead, both modes carry the bridge's loss, and the sustain sits at 2.8 seconds however much further the tuning is opened. The flat line is what the same two strings would do if they did not share a bridge. A chorused sound and a long one cannot be had from one bridge, and the first four and a half cents cost all of it.

The pair tuned apart on purpose

A piano's unison buys its sustain with a detuning of two and a half cents and loses it past four and a half. Read from the other side that is a design constraint on every instrument that wants the beating instead: past the bifurcation the sustain is gone and no further detuning costs anything more, which is why every chorused voice in the world — the celeste rank, the musette reeds, the paired gamelan — is built out of sources that do not share a bridge.

tuning · Beating 4 bores of one length, and the series each supports. cylinder, cone, exponential horn, Bessel horn — every one of them 148 cm long, 5.5 mm at the throat and 62 mm at the mouth, so the only thing that differs is the shape between the two. Beside each is the series of resonances Webster's equation gives it, and the number is how far that series is from evenly spaced, in cents. cylinder: 0.0 cents, with each mode sitting at minus 0.50 of a spacing off a whole multiple; cone: 9.6 cents, with each mode sitting at minus 0.12 of a spacing off a whole multiple; exponential horn: 22.8 cents, with each mode sitting at minus 0.16 of a spacing off a whole multiple; Bessel horn: 3.7 cents, with each mode sitting at minus 0.11 of a spacing off a whole multiple.

Only two shapes make a series

A tube's length sets where its modes are and its shape sets whether they are a series at all — and of every shape a maker could choose, exactly two give evenly spaced modes. Neither of them is the shape of a trumpet. Webster's equation says how far the others miss by, and the answer is a quarter of a semitone for the obvious ones and four cents for the family brass bells actually belong to.

instruments · Bore profile What a trumpet mouthpiece does to the series. Each bore's modes before a mouthpiece is fitted and after, on the axis that says which harmonic each mode is: zero means the m-th mode sits at m times the spacing and is the m-th harmonic. Every shape starts near -0.14 and ends near 0.05. The cup holds 3.0 millilitres against a throat 3.7 mm across and pops at 642 hertz. What does not improve is the regularity: the spacing stays as uneven as the flare left it.

What the mouthpiece is actually for

A cup and a throat look like a comfort fitting and are a component. Put a real one on the front of a real bore in the horn equation and the whole mode series slides sideways by about a seventh of its own spacing — which is exactly the distance between a series whose second resonance is 1.85 times the spacing and one whose second resonance is the second harmonic. The flare decides whether the modes are evenly spaced; the mouthpiece decides which harmonic each one is.

timbre · Bore profile cylinder and Bessel flare: the length each mode behaves as though it has. Each mode's own acoustic length, m·c over twice its frequency, for a bore 148 cm long. A cylinder would give one number repeated. This gives 164 cm at the second mode and 154 at the 8th — a spread of 10.1 centimetres, or 110 cents, because a flare's end correction is a length that shrinks as the note rises. The first mode is off the top of this axis and is not a mode a player uses.

A horn has one length per partial

Every tube until now has had an acoustic length: its physical length plus a correction for the wave carrying on past the opening. A flaring bore does not have one. Its second mode behaves as though the tube were 164 centimetres long and its eighth as though it were 154, and the ten centimetres between them are the same physical fact — a fixed correction against a shrinking wavelength — arriving as a hundred cents.

tuning · Bore profile The hand closing, and the note it is holding. The fourth resonance of a 370 cm horn against how much of the bore the hand occludes, at 97 per cent of the way along where the radius is 36 mm. Nothing much happens for the first ninety per cent. The note then falls to -401 cents — most of a fourth — over the next few, and between 99.5 and 99.90 per cent it jumps to 96 cents SHARP, because the lowest resonance has left the bottom of the range and every mode has taken the place of the one below it. The series' ratios are unchanged across the jump.

The hand goes in, and the note jumps

A horn player's hand closes the bell and the pitch falls — 19 cents, then 55, then 132, then four hundred, accelerating the whole way. Then, in the last half per cent of closure, it stops falling and lands a semitone above where it started. An earlier essay guessed the mechanism was the boundary condition changing kind and the series going odd-only. It is not. The series never changes at all.

tuning · Air column The first five peaks, followed as the hand closes. Each line is one member of the series, tracked by its rank rather than by its frequency, and each dot's size is that peak's height. The lowest peak falls from 38 hertz to 34 as the hand closes and then jumps to 45, which is the renumbering computed earlier: past the wall the series is one member shorter at the bottom and every peak has taken the place of the one below it. The dots shrink through the middle of the travel and grow again at the far end, so the transition costs the player support as well as pitch — and the cost is temporary, which is why a fully stopped horn is a usable instrument and a nearly stopped one is not.

A resonance has a strength as well as a frequency

What eleven earlier essays drew is a row of frequencies, because the solver behind it has no losses and a lossless resonance has no width. Put the losses in and every one of them acquires a height and a Q — and the hand closing a horn's bell turns out to take away nine and a half per cent of the instrument's total support before giving all of it back, in a window a few per cent wide where the horn is genuinely hard to play.

tuning · Air column The cutoff computed from the shape, and the cutoff read off the measurement. Two numbers for the same boundary. The hollow point is Webster's local cutoff — the largest value of (c/2π)√Γ along the bore, which is geometry alone. The filled point is where the impedance peaks stop, which is what a maker measures with a loudspeaker and a microphone. cone: no geometric cutoff at all, and peaks stopping at 4731; exponential horn: 89 hertz from the geometry, and peaks stopping at 2614, a factor of 29.26; catenoidal horn: 115 hertz from the geometry, and peaks stopping at 2499, a factor of 21.76; Bessel horn: 1154 hertz from the geometry, and peaks stopping at 1593, a factor of 1.38; cylinder and Bessel flare: 2945 hertz from the geometry, and peaks stopping at 4417, a factor of 1.50. The published figure for a trumpet is about 1500 hertz, marked. The two agree within about half for a bore whose flare is concentrated at the end and disagree by more than an order of magnitude for one whose flare is spread along it, which says what the local formula is and is not a measurement of.

The cutoff a maker can actually measure

A trumpet's bell cutoff computed from the geometry alone comes to 1,150 hertz against a published 1,500, and the calibration was the first thing that left owing. Measuring the model the way a maker measures the instrument — sweep a loudspeaker in, find where the impedance peaks stop — gives 1,593. The discrepancy was almost entirely in the formula, and on a bore whose flare is spread rather than concentrated the same formula is out by a factor of twenty-nine.

instruments · Bore profile Second order and fourth order, from the same sequence of wavenumbers. Frequency against wavenumber for a string and for a bar, with each object's own wavenumbers marked on the axis. A string's equation is second order in space, so frequency goes as wavenumber and the straight line carries its modes at 1, 2, 3, 4. A bar's is fourth order, so frequency goes as the SQUARE of wavenumber and the parabola carries the same kind of sequence to 1, 2.757, 5.404, 8.933. Both sequences of wavenumbers are arithmetic — a string's are the even multiples of π/2L and a bar's the odd ones, except that the first is 3.011 rather than 3 — and squaring an arithmetic sequence is the whole of why one object has a fundamental and the other has none. Every number is derived from the boundary condition; none is measured.

A bar's partials are the odd numbers, squared

A string's wave equation is second order in space and a bar's is fourth, so a string's frequencies go as its wavenumbers and a bar's go as their squares. Both objects fit a nearly arithmetic sequence of wavenumbers between their ends; squaring one is the whole of why a marimba key has no note in it. The ratios are 1 : 2.756 : 5.404 : 8.933, which are the odd squares over nine, uniformly 12.9 cents flat, and the 12.9 cents is one root that refused to be 3π/2.

instruments · Struck bar

Named alongside it

The objects these essays reach for when they reach for this one.

BoreBrassResonanceBoundary conditionHorn equationHarmonic seriesStanding waveCutoffDampingEnd correctionImpedanceBeating

All concepts