Series

Harmonic series — the series

14 essays on one idea, from the one that introduces it to the one that assumes the rest.
  1. The first eight partials of a string. A string vibrating in one, two, three and more equal parts, with the frequency ratio and the nearest named note beside each. The seventh partial is a third of a semitone flat of anything on a keyboard, which is a fact about strings rather than about tuning.

    A string does everything at once

    A plucked string does not vibrate at one frequency. It vibrates at all the whole-number multiples of one frequency simultaneously, and nearly everything in music theory is downstream of that fact.

    part 1 · timbre
  2. Where a tuned piano actually sits. The departure from equal temperament of every key of a small upright, computed from the stiffness of its strings and the fact that a tuner sets octaves without beats rather than at a ratio of two to one. The treble ends up 52 cents sharp and the bass 18 cents flat, and neither is an error.

    The piano is tuned wrong on purpose

    Every well-tuned piano has a sharp treble and a flat bass, by up to a third of a semitone at the extremes. It is not an error, it is not a compromise about keys, and it follows from one property of a steel wire that can be computed from its diameter and its length.

    part 2 · timbre
  3. Where to stop, and what stopping there gives. Each prefix of the harmonic series sounded as a chord of pure tones, with its roughness per pair and the pitch classes it contains. The smoothest prefix is the first 4, which is a bare fifth and an octave; roughness rises monotonically from there, so no roughness argument selects six. The prefixes that contain a major triad and nothing else are 5 and 6. One partial further and it is a dominant seventh; four further and there are five pitch classes. Six is the last stopping point that gives the answer the derivation wants, and nothing else in the arithmetic picks it out.

    The series is not a chord

    The major triad is derived from the first six partials of the harmonic series in every textbook that derives it from anything, and the derivation works: the first six contain a major triad and nothing else. Take the first four instead and there is no third at all; take seven and there is a dominant seventh with a flat seventh thirty-one cents below any keyboard note; take sixteen and there are eight pitch classes. Six is the last stopping point that gives the answer, roughness prefers three, four or ten depending on the register, and no criterion in the arithmetic selects six over any of them.

    part 3 · intervals
  4. The series has three tops. Where the harmonic series stops, asked three ways, at four fundamentals. Consecutive partials stop being separately resolvable around partial 8 — that one depends on the fundamental, since a critical band is a fixed width in hertz and the spacing is not. They stop being a semitone apart at partial 17 at every fundamental, because the ratio (n+1)/n does not know what n is measured in. And they stop being distinguishable in pitch at all between partials 34 and 140. Every claim about how far up the series something happens is a claim about which of these three was meant.

    The series has three tops

    How far up the harmonic series can an ear go? The question has three answers and they are an order of magnitude apart. Consecutive partials stop being separately resolvable somewhere around the eighth, and where exactly depends on the fundamental. They stop being a semitone apart at the seventeenth, at every fundamental, because the ratio does not know what it is measured in. And they stop being distinguishable in pitch at all between the thirty-fourth and the hundred and fortieth. Every claim about where the series runs out is a claim about which of the three was meant.

    part 4 · intervals
  5. Every modern bell puts the boundary at the same partial. For each brass instrument, the partial at which its bell stops turning the wave round — the frequency at which half the energy escapes at the mouth, divided by the tube's own fundamental. The five modern instruments land between partial 8.4 and partial 10.2 despite tube lengths differing by a factor of four, because a bell is scaled with its instrument. The natural trumpet of the baroque, whose bell is small and whose tube is long, puts it at partial 17.2.

    The fourth top is the maker's

    The series has three tops and all three are the ear's: where consecutive partials stop being resolved, where their spacing falls below a semitone, and where it falls below what the ear can hear at all. The fourth is how far up a player can go, and it is the only one somebody chose. Every modern brass bell puts the boundary at about the ninth partial across a family whose tubes differ by a factor of four — and the baroque natural trumpet, whose bell is small, puts it at the seventeenth, which is exactly the top of the clarino register.

    part 5 · intervals
  6. The flare that makes a series harmonic, and how narrow it is. Every combination of a flare exponent and a station at which the flare begins, shaded by how far the bore's resonance series is from a harmonic series over partials 2 to 8, in cents. The best is 4.6 cents at an exponent of 1.00 beginning 43 per cent of the way along, against 127 cents for a plain cylinder, 21 for a plain cone and 26 for a Bessel horn of the exponent used everywhere else. Only 2.1 per cent of the surface is within five cents of the minimum, so the shape is forced rather than chosen — which is what three centuries of empirical brass design were finding.

    The flare that makes a series harmonic

    Every figure until now treats a partial as n times a fundamental, and the whole of brass instrument design is the business of making that true. A plain cylinder is 127 cents from a harmonic series and a plain cone is 21; the best flare found by sweeping is 4.6, and only two per cent of the swept surface comes within five cents of it. The shape is forced rather than chosen.

    part 6 · timbre
  7. The bell and the cup, on one surface. Every combination of a flare exponent and a cup depth, shaded by how far the resonance series is from a harmonic series over partials 2 to 8, in cents. The pale line is the best flare for each cup — the ridge — and it runs diagonally: the exponent that suits the shallowest cup here is 0.93 and the one that suits the deepest is 0.70, a spread of 0.22. The ring marks the bell found earlier by sweeping the flare alone, at an exponent of 1.00 — which reaches 4.6 cents with nothing in front of it, and sits where the ring is, at 24.9 cents, once a catalogue mouthpiece is on it. It is on none of the ridge, and that is the whole finding: the two choices are not separable, and a bell optimised alone is not the bell an instrument wants.

    The bell is tuned for the cup

    Sweeping a brass bell's two flare parameters found a shape that makes the resonance series harmonic to four and a half cents. Bolt the mouthpiece that instrument is actually played with onto it and the series is twenty-five cents out — worse than a plain cone. The flare and the cup are not two independent choices, and the best bell for a maker to build is one that is deliberately wrong.

    part 7 · timbre
  8. The bare bore does not care which valve is down. The distance in cents of partials 2 to 8 from the harmonic series that fits them best, at each valve combination of a B♭ trumpet, computed with the mouthpiece in place and again with the bore alone. The bare bore is flat — 0.78 cents from best to worst across the whole set — so the length changes nothing. With one cup serving all of them the same bore runs 19.53 to 24.83 cents, a spread of 5.30, because the cup's popping frequency stays at 642 hertz while the series underneath it drops.

    One cup and seven lengths

    A trumpet is seven tubes with one mouthpiece serving all of them, and the harmonicity of its resonance series is a different number in every position — 19.5 cents open, 24.8 with all three valves down. The bare bore is flat across the same seven lengths to within eight-tenths of a cent, so none of it is a length problem. It is the cup, standing still while the series walks past it, and pressing all three valves does to the series exactly what fitting a mouthpiece 56 per cent of the catalogue depth would do.

    part 8 · timbre
  9. The top of a struck note's series falls while the note lasts. The highest partial still above the threshold of hearing, against time, for a note struck at 80 decibels on a fundamental of 130.8 hertz with a 1/n spectrum and a loss rising as the partial number to the power 1. It starts at partial 152 and it is falling from the first millisecond. The horizontal lines are the three tops computed from frequency alone, all of which assume a note that never ends: the note's own top drops past the difference-limen top after 0.03 seconds, past the semitone top after 0.32, and past the resolvable top after 0.64. After that the series is shorter than the ear could have resolved, and what stops it is the clock.

    The top that falls while the note lasts

    Four earlier essays have asked where the harmonic series stops, and all four answered with a number computed for a tone that never ends. A struck C3 has 152 audible partials at the strike and eight after two-thirds of a second, so the ear's own resolution limit governs the first ten per cent of the note and the decay governs the rest. Playing ten decibels louder buys the ear a further tenth of a second, and doubling its reign would take fifty-eight.

    part 9 · timbre
  10. Both notes of a fifth, and the coincidences going out. The highest partial still above the threshold of hearing for each note of a fifth struck at 80 decibels on 130.8 hertz, against time, with a 1/n spectrum and a loss rising as the partial number to the power 1. Both curves come down from off the top of the frame — the lower note starts with 152 partials and the upper with 102, because twenty kilohertz is a ceiling in frequency and not in partial number. The rings are the interval's partial coincidences at the moment they stop existing — successive multiples of one ratio, which go out from the top down: 12:8 at 0.47 s, then 9:6 at 0.64 s, then 6:4 at 1.04 s, then 3:2 at 2.14 s. The lowest, 3:2, is the last, and after it the two notes have no partial in common that either of them can still supply.

    A fifth on a piano is not a fifth a second later

    Nine essays draw one note in silence, and a listener is given a texture. Put two struck notes an interval apart and consonance comes apart into two quantities that had agreed while nothing moved: the partial coincidence that names the interval outlives the strike in exactly the order common-practice theory ranks its intervals, and the roughness that scores it reorders itself inside a third of a second, with the fifth overtaken by four intervals every treatise calls harsher.

    part 10 · timbre
  11. An inversion lasts as long as its outer sixth. The six three-note voicings of a major and a minor triad, each over a bass of C3 struck at 80 decibels, with how long the strongest partial coincidence of each of its three intervals survives the strike. The interval that goes first is marked, and its time is how long the chord keeps the evidence of all its intervals at once. major, root position: major third 5:4 1.26 s, minor third 6:5 1.03 s, fifth 3:2 2.14 s; the chord 1.03 s. major, sixth chord: minor third 6:5 1.04 s, fourth 4:3 1.62 s, minor sixth 8:5 0.74 s; the chord 0.74 s. major, six-four: fourth 4:3 1.60 s, major third 5:4 1.27 s, major sixth 5:3 1.26 s; the chord 1.26 s. minor, root position: minor third 6:5 1.04 s, major third 5:4 1.27 s, fifth 3:2 2.14 s; the chord 1.04 s. minor, sixth chord: major third 5:4 1.26 s, fourth 4:3 1.63 s, major sixth 5:3 1.26 s; the chord 1.26 s. minor, six-four: fourth 4:3 1.60 s, minor third 6:5 1.03 s, minor sixth 8:5 0.74 s; the chord 0.74 s. The major six-four lasts longest and the major sixth chord shortest; every root position is held to its minor third's life.

    An inversion lasts as long as its outer sixth

    A struck interval keeps the partial coincidence that names it for a time set by its ratio, and a chord is three intervals at once. Voiced over one bass and struck on a piano, a triad keeps the evidence of all three only as long as its weakest one lasts, and for an inversion that is the sixth on the outside: a major sixth lasts as long as a major third, a minor sixth dies first. So the major six-four and the minor sixth chord are the most durable voicings of their triads and the major sixth chord and the minor six-four the least — and unlike a dyad, a triad's inversions keep their order by roughness through almost the whole decay.

    part 11 · timbre
  12. Opening a triad changes which interval goes first. The six voicings of a major and a minor triad over C3, each close and with its middle note raised an octave, struck at 80 decibels, with how long each keeps the coincidences of all three of its intervals and which interval goes first. major root position: close 1.03 s, held by its minor third 6:5; open 1.26 s, held by its major tenth 5:2. major sixth chord: close 0.74 s, held by its minor sixth 8:5; open 0.47 s, held by its minor tenth 12:5. major six-four: close 1.26 s, held by its major sixth 5:3; open 0.74 s, held by its eleventh 8:3. minor root position: close 1.04 s, held by its minor third 6:5; open 0.47 s, held by its minor tenth 12:5. minor sixth chord: close 1.26 s, held by its major third 5:4; open 1.26 s, held by its major sixth 5:3. minor six-four: close 0.74 s, held by its minor sixth 8:5; open 0.74 s, held by its minor sixth 8:5.

    An open triad lasts as long as its tenth

    Close, every triad's weakest link is a third or a sixth. Raise its middle note an octave and the link becomes a compound interval, and compound intervals do not last alike: a major tenth, 5:2, lives as long as a major sixth, while a minor tenth, 12:5, needs the twelfth partial and lives 0.47 seconds. So the spacing orchestration manuals recommend for a major chord in the bass is the longest-lived voicing a struck triad has, and the same spacing halves the life of a minor chord — and the six-four's advantage reverses.

    part 12 · intervals
  13. Both qualities reach the same ceiling. The longest-lived spacing of a major triad and of a minor one, over four basses, taken over every arrangement of the three pitch classes within 2 octaves. They are the same number at every bass — 1.16 seconds over C2, 1.26 seconds over C3, 1.26 seconds over C4, 1.41 seconds over C5 — and at each bass 2 major and 2 minor spacings are tied at it. The faint line is the worst a minor spacing can do, which is 3.5 times shorter. So the asymmetry found earlier is a fact about the minor tenth rather than about the minor triad: a minor chord has a spacing that avoids it, and that spacing is its first inversion, where the minor third between two of its notes appears as a major sixth instead.

    A minor triad can be spaced to last

    Two spacings of each triad, drawn side by side, say that opening lengthens a major chord and halves a minor one. Drawn over every arrangement of the three pitch classes within two octaves of a fixed bass, the asymmetry disappears: a minor triad reaches 1.26 seconds over C3 and so does a major one, with two spacings of each tied at the top. The short-lived chords were never the minor ones. They were the ones with a minor tenth on the outside, and a minor triad has three spacings that avoid it.

    part 13 · intervals
  14. No seventh chord can be spaced to last as long as a triad. Every inversion and spacing within 2 octaves over C3, struck at 80 dB, for two triads and five seventh chords: the bar is the longest any spacing keeps every pair's partial coincidence, and the tick is the bound set by the chord's worst pitch-class distance — the longest any presentation of that distance lasts. major triad: 1.26 s over 12 voicings, bound 1.26 set by the minor third; minor triad: 1.26 s over 12 voicings, bound 1.26 set by the minor third; dominant seventh: 0.66 s over 32 voicings, bound 0.64 set by the tone; major seventh: 0.42 s over 32 voicings, bound 0.38 set by the semitone; minor seventh: 0.69 s over 32 voicings, bound 0.64 set by the tone; half-diminished seventh: 0.69 s over 32 voicings, bound 0.64 set by the tone; diminished seventh: 0.86 s over 32 voicings, bound 0.87 set by the tritone. Every seventh chord contains a distance worse than any a triad contains, except the diminished seventh, whose distances are only minor thirds and tritones.

    A seventh chord cannot be spaced to last like a triad

    A struck triad keeps the partial coincidences of all its intervals for at most 1.26 seconds, whichever way it is spaced. Run the same census over every inversion and spacing of five kinds of seventh chord and none gets near: the dominant, minor and half-diminished sevenths top out at about two thirds of a second, the major seventh at 0.42. The diminished seventh, which theory calls the least stable of them, lasts longest at 0.86 — because it is the only one with no tone or semitone among its pitch-class distances, and the worst distance a chord contains sets a ceiling no spacing can lift.

    part 14 · timbre

All series